Control4 CCZ-T1-W Installationsanleitung Seite 1

Wireless Thermostat Installation Guide

Zoned SystemsControl4 supports zoned HVAC systems using a zoning panel. If used, however, a common wire needs to be installed at the Thermostat. Power

Place the Wireless Thermostat in a proper location to ensure its eciency and to avoid unnecessary cycling of the furnace or air conditioner.a. Plac

Thread the wires from the wall through the back of the large rectangu-lar opening in the new rear plate (see Figure 3), and then position the new rear

Select the desired power supply method by enabling or disabling power stealing on the back of the Thermostat faceplate.• Disable (recommended). Power

16Install the CR123A (3V) battery (included) in the Thermostat faceplate according to the polarity labels—POS (+) and NEG (-)—on the Thermostat’s cir

Composer Programming InstructionsAll advanced programming must be completed by a Control4 Dealer using Composer Pro. To see what advanced programming

PropertiesFahrenheit or Celsius: Sets the temperature display in Fahrenheit or Celsius. View/Edit Schedule: Select to access and edit the Thermostat s

Time FormatDate Format: Sets the format preferences for date (MM/DD/YYYY or DD/MM/YYYY).Time Format: Sets the format preferences for time (12h or 24h)

to 2 degrees, the heating system will engage until reaching 70 degrees Fahrenheit.Cooling Cuto Point: Sets the temperature for the cooling system to

Maximum Run Time: Sets the maximum time heating or cooling will run before turning o. To adjust, use the up and down arrows. Example: If cooling or h

DisclaimerTrademarksWarrantyControl4® makes no representations or warranties with respect to any Control4 hardware, software, or the contents or use o

Thermostat RelaysThis section shows the relays that are engaged during heating and cooling for the various Wire-less Thermostat configurations.Conventi

Primary Fan (Electric), Secondary Fan (Electric)Stage Y1 Y2 W1 W2 O B G1st Stage * *2nd Stage * * *• The switch in the fuel position causes the Therm

Primary Fan (Electric), Secondary Fan (Electric)Stage Y1 Y2 W1 W2 O B G1st Stage * *2nd Stage * * *Primary Fan (Fuel), Secondary Fan (Electric)Stage Y

Primary Fan (Electric), Secondary Fan (Fuel)Stage Y1 Y2 W1 W2 O B G1st Stage * * *2nd Stage * * * *3rd Stage (Before Aux Stage Delay)* * * * *Auxiliar

Primary Fan (Electric), Secondary Fan (Electric)Stage Y1 Y2 W1 W2 O B G1st Stage * * *2nd Stage * * * *3rd Stage * * * * *E-Heat (Stage 1)* * *• The

Heat Pump: CoolingPrimary Fan (Fuel), Secondary Fan (Fuel)Stage Y1 Y2 W1 W2 O B G1st Stage * * *2nd Stage * * * *Primary Fan (Electric), Secondary Fan

TroubleshootingIf the Thermostat is not working:1. Ensure that the HVAC system is not turned OFF.2. Check for proper wiring (see “Sample Wiring Confi

Installing a Bypass Resistor to Enable Power Stealing on a Wireless ThermostatAlthough Control4 recommends using a common wire to provide power to the

Access the 24V transformer and integrated control panel on the HVAC system. This typically requires removing the front panel of the furnace. Remember

25Figure 7. Gas/Electric Single Stage

Table of ContentsiiiSupported Model ... 1Impo

Loosen the screw on the heat terminal (typically marked ‘W’ or ‘W1’) and secure one end of the resistor in the HVAC system’s Heat Relay Terminal by ti

Example 2. This second example (Figure 9) shows a control board that does not provide a common wire screw terminal. In this example, an additional len

Sample Wiring ConfigurationsWARNING! Do not install LINE VOLTAGE wires to a LOW VOLTAGE wire. IMPORTANT! When utilizing power stealing, Control4 recomm

29Wiring ConnectionsTerminal DescriptionRH 24VAC power for heating—connect to low voltage heating system transformer. (See Note 1 below.)RC 24VAC pow

30Figure 10. Conventional, Single Stage Wiring

31Figure 11. Conventional, Dual Stage Wiring

32Figure 12. Heat Pump, Single Stage Wiring

33Figure 13. Heat Pump with Electric Auxilliary Heat, Dual Stage Wiring

34Figure 14. Millivolt Heat, Conventional Cool, Single Stage Wiring

35Figure 15. Heat Pump with Electric Auxilliary, Dual Stage, Dual Transformer Wiring

Regulatory ComplianceTo review regulatory information for your particular Control4 products, see the information located on the Control4 website at: h

Supported ModelCCZ-T1-W Wireless Thermostat - WhiteWARNING! Install in accordance with all national and local electrical codes.WARNING! This pro

Box Contents• Wireless Thermostat• CR123A (3V) battery• 3 screws (#6 x 1-inch sheet metal screws)• 3 plastic wall anchors (#4-6 x 7/8”)• Warranty

SpecificationsFront and Rear ViewFigure 1. Faceplate Figure 2. Rear PlateRecommended Wiring: 22 AWG (36 ft. max.) 18 AWG (100 ft. max.)Power Sour

IMPORTANT! The Wireless Thermostat has ‘power stealing’ enabled by default, however, it is recommended to power the Thermostat with a common wire. If

• New construction, Control4 recommmends these options:• Install a common wire.• Use a Remote Temperature Sensor in the wall where the Thermostat i